Emissions Reduction Alberta (ERA) will pay up to half the eligible cost of a methane project, and a lot of operators still have not looked at it. Here is how ERA funding in Alberta works, in plain words, and where it can catch you out.
What the program is
ERA runs the Methane Reduction Deployment Program. It pays up to 50% of the eligible cost of a project that cuts methane at an existing Alberta oil and gas facility. Think pneumatics, venting from tanks and compression, casing gas capture, surface casing vent flow and engine methane slip. Intake is continuous, so there is no window to wait for.
The money is not unlimited. ERA’s June 2026 webinar put the program at $41.8 million in total, and funding is first come, first served until the program ends on March 31, 2029 or the money is gone.
Who can apply
Upstream and midstream oil and gas operators in Alberta. The operator or facility owner applies, not the contractor. It has to be an existing facility, not new construction, and the project has to cut methane beyond what the regulations already require. Leak detection on its own does not qualify, and neither does sending the captured gas to a flare. Monitoring only counts when it is bundled with a technology that actually reduces emissions.

Facilities under TIER are now in. ERA’s updated program rules, dated August 2026, make TIER-regulated facilities eligible, including large final emitters. There is a catch: a large final emitter or opted-in facility has to be part of an application made before March 31, 2028. In June, ERA’s webinar still said TIER facilities were out unless they were part of an aggregate, so if you wrote this program off earlier, it is worth a second look. Our ERA funding application support page shows what to have ready before you apply.
The numbers
- Up to 50% of eligible project costs.
- Smallest request: $25,000.
- Cap: $1 million per technology type and $2 million per parent company.
- Engine methane slip projects share a $15 million pot across the whole program.
- Overhead and internal costs count up to 15%, and front end engineering up to 10%.
ERA’s own worked example shows how the caps bite. One company applies for three projects:
| Project | Eligible cost | Funding approved |
|---|---|---|
| Pneumatics | $1.9M | $0.95M (50%) |
| Methane slip | $2.5M | $1.0M (technology cap) |
| Routine venting | $0.4M | $0.05M (company cap) |
| Total | $4.8M | $2.0M |
So a $400,000 pneumatics retrofit on its own could bring back up to $200,000. Stack three projects and the company cap decides the answer, not the 50%. Vent gas capture work, like the projects on our vent gas reduction projects page, sits in the routine venting and casing gas categories.
Dates and timing
There is no application deadline to chase, apart from the March 2028 cut-off above for large final emitters. Submitting an application does not hold your spot. ERA only reserves funding once the participant agreement is signed. Only costs spent between November 12, 2025 and March 31, 2029 count, and the project has to be finished within two years of the signed agreement or by March 31, 2029, whichever comes first. You can start before approval, but that is at your own risk.
Other government funding can sit alongside ERA’s if you disclose all of it and the total does not go over 100% of project costs. Money spent only to create carbon credits is not covered.
Stacking ERA funding with carbon offset credits
Taking ERA funding does not cost you the credits. ERA’s FAQ says MRDP funding may be combined with revenue from emission offset credits, as long as the project meets the program’s eligibility requirements and follows the relevant Alberta offset protocol. Participants can also generate and keep emission performance credits. Under ERA’s August 2026 terms, that applies to applications submitted before March 31, 2028.
Take the $400,000 pneumatics retrofit above. ERA could cover up to $200,000 of it, and the credits from the avoided venting are sold on top. What they are worth depends on the tonnes the project avoids and the market price.
Two things to get right:
- Disclose your other funding. You can stack ERA with other programs, but the total cannot go over 100% of project costs.
- Budget the credit work yourself. ERA does not fund the costs of generating credits, such as registering the project and verifying the reductions.
The project also has to follow the Alberta offset protocol for its type. On November 12, 2026, Alberta’s offset system listing showed the Pneumatic Devices protocol at version 3.0 and the Vent Gas Reduction protocol at version 2.0. Check the listing for the current version before you register, because protocols get revised. A memo dated February 27, 2026 adds a Category 3 to Vent Gas Reduction for surface casing vent flow destruction. A reduction that becomes required by law stops earning offsets from the day it becomes required. Our carbon offset management team works through exactly this.
Where to start
If you have a project in mind, we can tell you which credits it can earn and how to sequence the grant application and the offset registration, so neither costs you the other. For a shorter read on the program itself, see our earlier article, ERA methane reduction funding in Alberta.
Write to Cole Tomaszewski at Carbon Strategies: coletomaszewski@intricategroup.com You deal with ERA directly when you apply, and Cole can help you work out where to start.
The program details above come from ERA’s program FAQ, its August 2026 program guide and its June 25, 2026 webinar.



